Click here to Skip to main content
Click here to Skip to main content

Tagged as

Go to top

Netgear GS108 - 8 Blinking Link LEDs - Can we fix it? Yes we CAN!

, 1 Jun 2011
Rate this:
Please Sign up or sign in to vote.
Netgear GS108 8-port Gigabit switch is unhappy, only wants to blink.......blink no more!

Introduction

I was on a roll (I hoped), after successfully bringing back one of my dead JGS516 switches to life, it was time to turn the attention to another dead switch I had. Can I make it 2 for 2?

On the ground floor of the house, I had another network switch, this was for things like the TV, appleTV, etc. and as a backup for my laptop in the event my wireless went belly up. One afternoon, nothing would connect, and all 8 Link LEDs just blinked in unison.

Background

netgear_gs108.jpg

The switch in question is a Netgear GS108, 8-Port Gigabit Switch.

I purchased it in April 2007, and it had served me well for 4 years before going on the fritz. It was originally purchased for £51 (UK Pounds), and today a replacement would cost £50.

Diagnosis

WARNING: This repair involved the use of a soldering iron, and care should be taken to avoid burns, etc. Also observe suitable anti-static procedures to reduce the risk of damaging electronic components due to static discharges.........and another thing, always unplug before opening, and if in doubt, do not attempt to open anything.

The problem was that the device would no longer allow any connections, or traffic to pass across its ports, the Link LED of each port would flash on and off in unison.

After unplugging the unit, and undoing the screws at the back, I slid of the cover and inspected internally. There was no dust accumulations, no evidence of burning, and things looked relatively okay.

It wasn't until I took a closer look at the PCB, I observed that out of the 5 capacitors, 2 of these had slightly domed by about 1-2mm compared to the others. I suspected that these two capacitors had died of old age or whatever. I thought it would be worth a shot at changing them, as I had nothing to lose, and if it didn't work after this, I was going to need a new switch anyway. The 2 capacitors that had swollen are circled in the image below:

swollen_caps.jpg

The capacitors were 1000uf 6.3v 105'C polarized, so a quick trip to my local Maplin store, I picked up some slightly higher voltage rated 1000uf 16V 105'C. Maplin part number DT69A and at a cost of £0.44 each. I chose a higher voltage rating, just for the sake of it really, as it won't do any harm.

Now, the switch is a low profile unit, and although the capacitors would have probably fitted in just fine, I decided to knock these over at an angle, just to be on the safe side.

Powered up the soldering iron, whipped out the old capacitors, and installed the new ones. Refitted the PCB into the case, and took it for a spin. Worked first time, no issues.

replace_caps.jpg

Good as new! Another worthwhile home repair.

Switch Original Cost: £51

Switch Replacement Cost: £50

My Home Repair Cost: £0.88

So if you have a Netgear switch that is displaying the blinky flash of death, then it may be worth checking out the capacitors.....[after I fixed this, I did a search on Google and found others talking about the same fault].

May the Soldering Iron be with you!

History

  • V1.0, 1st June 2011 - First release

License

This article, along with any associated source code and files, is licensed under The Code Project Open License (CPOL)

Share

About the Author

DaveAuld
Engineer
Scotland Scotland
I have been working in the Oil & Gas Industry for over 20 years now.
 
Core Discipline is Instrumentation and Control Systems.
 
Completed Bsc Honours Degree (B29 in Computing) with the Open University in 2012.
 
Currently, Offshore Installation Manager for the Beryl Bravo platform, which is located ~180 miles NE of Aberdeen, Scotland in the Northern North Sea.
Formely on the Forties Charlie platform, which is located ~110Miles NE of Aberdeen.
Follow on   Twitter   Google+   LinkedIn

Comments and Discussions

 
GeneralAdvice Pinmemberdweight8-Jun-11 21:21 
GeneralRe: Advice PinmemberDaveAuld8-Jun-11 21:28 
GeneralSmart Cookie ... PinmemberGarth J Lancaster1-Jun-11 14:15 

General General    News News    Suggestion Suggestion    Question Question    Bug Bug    Answer Answer    Joke Joke    Rant Rant    Admin Admin   

Use Ctrl+Left/Right to switch messages, Ctrl+Up/Down to switch threads, Ctrl+Shift+Left/Right to switch pages.

| Advertise | Privacy | Mobile
Web04 | 2.8.140916.1 | Last Updated 1 Jun 2011
Article Copyright 2011 by DaveAuld
Everything else Copyright © CodeProject, 1999-2014
Terms of Service
Layout: fixed | fluid