|
|
/********************************************************************
FileName: HardwareProfile.h
Dependencies: See INCLUDES section
Processor: PIC18 or PIC24 USB Microcontrollers
Hardware: The code is natively intended to be used on the following
hardware platforms: PICDEM� FS USB Demo Board,
PIC18F87J50 FS USB Plug-In Module, or
Explorer 16 + PIC24 USB PIM. The firmware may be
modified for use on other USB platforms by editing this
file (HardwareProfile.h).
Complier: Microchip C18 (for PIC18) or C30 (for PIC24)
Company: Microchip Technology, Inc.
Software License Agreement:
The software supplied herewith by Microchip Technology Incorporated
(the �Company�) for its PIC� Microcontroller is intended and
supplied to you, the Company�s customer, for use solely and
exclusively on Microchip PIC Microcontroller products. The
software is owned by the Company and/or its supplier, and is
protected under applicable copyright laws. All rights are reserved.
Any use in violation of the foregoing restrictions may subject the
user to criminal sanctions under applicable laws, as well as to
civil liability for the breach of the terms and conditions of this
license.
THIS SOFTWARE IS PROVIDED IN AN �AS IS� CONDITION. NO WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED
TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. THE COMPANY SHALL NOT,
IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
********************************************************************
File Description:
Change History:
Rev Date Description
1.0 11/19/2004 Initial release
2.1 02/26/2007 Updated for simplicity and to use common
coding style
1.0 06/01/2008 Modified to be HIDAche firmware - HardlySoftware
Revision changed to 1.0 because it will be the
first release of HIDAche
********************************************************************/
#ifndef HARDWARE_PROFILE_H
#define HARDWARE_PROFILE_H
#define DEMO_BOARD
#define HIDACHE_BOARD
#if !defined(DEMO_BOARD)
#if defined(__C30__)
#if defined(__PIC24FJ256GB110__)
#define DEMO_BOARD PIC24FJ256GB110_PIM
#define EXPLORER_16
#define PIC24FJ256GB110_PIM
#define CLOCK_FREQ 32000000
#endif
#endif
#if defined(__18CXX)
#if defined(__18F4550)
#define DEMO_BOARD PICDEM_FS_USB
#define PICDEM_FS_USB
#define CLOCK_FREQ 48000000
#elif defined(__18F87J50) || defined(__18F85J50)
#define DEMO_BOARD PIC18F87J50_PIM
#define PIC18F87J50_PIM
#define CLOCK_FREQ 48000000
#endif
#endif
#endif
#if !defined(DEMO_BOARD)
#error "Demo board not defined. Either define DEMO_BOARD for a custom board or select the correct processor for the demo board."
#endif
//#define ENABLE_CONSOLE
/** TRIS ***********************************************************/
#define INPUT_PIN 1
#define OUTPUT_PIN 0
/** USB ************************************************************/
#if defined(HIDACHE_BOARD)
//#define USE_SELF_POWER_SENSE_IO
//#define USE_USB_BUS_SENSE_IO
//Prototype for the translate function
BOOL TranslateAsciiToHID(char asciiKey, char *hidKey, BOOL *needShiftKey);
#define PROGRAMMABLE_WITH_USB_HID_BOOTLOADER
#define U1ADDR UADDR
#define U1IE UIE
#define U1IR UIR
#define U1EIR UEIR
#define U1EIE UEIE
#define U1CON UCON
#define U1EP0 UEP0
#define U1CONbits UCONbits
#define U1EP1 UEP1
#define U1CNFG1 UCFG
#define U1STAT USTAT
#define U1EP0bits UEP0bits
#if defined(USE_USB_BUS_SENSE_IO)
#define USB_BUS_SENSE PORTAbits.RA1
#else
#define USB_BUS_SENSE 1
#endif
#define tris_self_power TRISAbits.TRISA2 // Input
#if defined(USE_SELF_POWER_SENSE_IO)
#define self_power PORTAbits.RA2
#else
#define self_power 1
#endif
// I leave this code here commented out in case I want to use a switch
// or LED for debug purposes.
/** LED ************************************************************/
//#define mInitAllLEDs() LATA &= 0x00; TRISA &= 0x00;
//#define statusLED LATAbits.LATA1
//#define statusLED_On() mLED_1 = 1;
//#define statusLED_Off() mLED_1 = 0;
//#define statusLED_Toggle() mLED_1 = !mLED_1;
/** SWITCH *********************************************************/
//#define mInitAllSwitches() TRISAbits.TRISA0=1;
//#define mSwitch PORTAbits.RA0
/** Pin Initialization *********************************************/
// Make all unused pins output and pull them low
#define InitializePins() TRISB = 0x00; TRISC &= 0x38; TRISA &= 0xC3; PORTA &= 0xC3; PORTB &= 0x00; PORTC &= 0x38;
// EEPROM MEMORY LAYOUT ********************************************
#define DEVICE_STRUCT_LOC 0x00
#define INTERVAL_LOC 0x0A
#define DEV_MODE_LOC 0x0B
#define MOUSE_MODE_LOC 0x0C
#define KEYS_LENGTH_LOC 0x0D
#define PHRASE_START_LOC 0x0E
// HIDACHE STRUCTURE DEFINITION ************************************
// The EEPROM layout for hidache is as follows:
// Interval - 0x0A
// Device Mode - 0x0B
// Mouse Mode - 0x0C
// Phrase Length - 0x0D
// Phrase - 0x0E - 0xFF
enum DEVICE_MODE
{
MODE_MOUSE = 0x00,
MODE_KEYBOARD = 0x01,
MODE_BOTH = 0x02
};//DEVICE_MODE;
enum MOUSE_MODE
{
MM_CIRCLE = 0x00,
MM_BOTTOM_LEFT = 0x01,
MM_TOP_RIGHT = 0x02,
MM_UP = 0x03,
MM_DOWN = 0x04,
MM_LEFT = 0x05,
MM_RIGHT = 0x06,
MM_RANDOM = 0x07,
MM_SIDE_TO_SIDE = 0x08
};//MOUSE_MODE;
enum SEND_TYPE
{
MOUSE = 0x00,
KEYSTROKE = 0x01
};
#endif
#if defined(PICDEM_FS_USB)
//The PICDEM FS USB Demo Board platform supports the USE_SELF_POWER_SENSE_IO
//and USE_USB_BUS_SENSE_IO features. Uncomment the below line(s) if
//it is desireable to use one or both of the features.
//#define USE_SELF_POWER_SENSE_IO
//#define USE_USB_BUS_SENSE_IO
#define PROGRAMMABLE_WITH_USB_MCHPUSB_BOOTLOADER //Uncomment this to make the output HEX of this project work with the MCHPUSB Bootloader
#define U1ADDR UADDR
#define U1IE UIE
#define U1IR UIR
#define U1EIR UEIR
#define U1EIE UEIE
#define U1CON UCON
#define U1EP0 UEP0
#define U1CONbits UCONbits
#define U1EP1 UEP1
#define U1CNFG1 UCFG
#define U1STAT USTAT
#define U1EP0bits UEP0bits
#define tris_usb_bus_sense TRISAbits.TRISA1 // Input
#if defined(USE_USB_BUS_SENSE_IO)
#define USB_BUS_SENSE PORTAbits.RA1
#else
#define USB_BUS_SENSE 1
#endif
#define tris_self_power TRISAbits.TRISA2 // Input
#if defined(USE_SELF_POWER_SENSE_IO)
#define self_power PORTAbits.RA2
#else
#define self_power 1
#endif
// External Transceiver Interface
#define tris_usb_vpo TRISBbits.TRISB3 // Output
#define tris_usb_vmo TRISBbits.TRISB2 // Output
#define tris_usb_rcv TRISAbits.TRISA4 // Input
#define tris_usb_vp TRISCbits.TRISC5 // Input
#define tris_usb_vm TRISCbits.TRISC4 // Input
#define tris_usb_oe TRISCbits.TRISC1 // Output
#define tris_usb_suspnd TRISAbits.TRISA3 // Output
/** LED ************************************************************/
#define mInitAllLEDs() LATD &= 0xF0; TRISD &= 0xF0;
#define mLED_1 LATDbits.LATD0
#define mLED_2 LATDbits.LATD1
#define mLED_3 LATDbits.LATD2
#define mLED_4 LATDbits.LATD3
#define mLED_1_On() mLED_1 = 1;
#define mLED_2_On() mLED_2 = 1;
#define mLED_3_On() mLED_3 = 1;
#define mLED_4_On() mLED_4 = 1;
#define mLED_1_Off() mLED_1 = 0;
#define mLED_2_Off() mLED_2 = 0;
#define mLED_3_Off() mLED_3 = 0;
#define mLED_4_Off() mLED_4 = 0;
#define mLED_1_Toggle() mLED_1 = !mLED_1;
#define mLED_2_Toggle() mLED_2 = !mLED_2;
#define mLED_3_Toggle() mLED_3 = !mLED_3;
#define mLED_4_Toggle() mLED_4 = !mLED_4;
/** SWITCH *********************************************************/
#define mInitAllSwitches() TRISBbits.TRISB4=1;TRISBbits.TRISB5=1;
#define mInitSwitch2() TRISBbits.TRISB4=1;
#define mInitSwitch3() TRISBbits.TRISB5=1;
#define sw2 PORTBbits.RB4
#define sw3 PORTBbits.RB5
/** POT ************************************************************/
#define mInitPOT() {TRISAbits.TRISA0=1;ADCON0=0x01;ADCON2=0x3C;ADCON2bits.ADFM = 1;}
/** SPI : Chip Select Lines ****************************************/
#define tris_cs_temp_sensor TRISBbits.TRISB2 // Output
#define cs_temp_sensor LATBbits.LATB2
#define tris_cs_sdmmc TRISBbits.TRISB3 // Output
#define cs_sdmmc LATBbits.LATB3
/** SD/MMC *********************************************************/
#define TRIS_CARD_DETECT TRISBbits.TRISB4 // Input
#define CARD_DETECT PORTBbits.RB4
#define TRIS_WRITE_DETECT TRISAbits.TRISA4 // Input
#define WRITE_DETECT PORTAbits.RA4
#endif
#endif //HARDWARE_PROFILE_H
|
By viewing downloads associated with this article you agree to the Terms of Service and the article's licence.
If a file you wish to view isn't highlighted, and is a text file (not binary), please
let us know and we'll add colourisation support for it.
Submit an article or tip