|
Oh, if only this was (4,3,4,1,4)
|
|
|
|
|
The man and a Book
|
|
|
|
|
Erm ... no.
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
BTW is there a comprehensible solution for this?
|
|
|
|
|
Oh yes.
Would I have posted it if there wasn't?
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
OriginalGriff wrote: Would I have posted it if there wasn't? Can't answer for you!
|
|
|
|
|
Hmm, I suspect OG has not got a clue, much like the CCC
|
|
|
|
|
I've posted this on here before it's his age
Edit
Ooops no I haven't but it's similar
"We can't stop here - this is bat country" - Hunter S Thompson - RIP
|
|
|
|
|
And that's your age, you cheeky young scamp!
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Fueled By Caffeine wrote: Hmm, I suspect OG has not got a clue, much like the CCC
You are up tomorrow!
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Yes my clue was 1,4,1,4 (1,4,1,4) which was I aint a clue
"We can't stop here - this is bat country" - Hunter S Thompson - RIP
|
|
|
|
|
This isn't original to me, but I liked it so much I wanted to use it!
No idea where the original was, unfortunately, I found it here: A few of her favourite clues - Telegraph[^]
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Yes they're good clues - I think I might of plagiarised mine from my hippy Grauniad days - H,I,J,K,L,M,N,O (5) is another of my favourites
"We can't stop here - this is bat country" - Hunter S Thompson - RIP
|
|
|
|
|
WATER: 'H' 2 'O'
I liked the "Drop the Dead Donkey" one as well: "Gegs (9, 4)"
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
What's the answer ?
"We can't stop here - this is bat country" - Hunter S Thompson - RIP
|
|
|
|
|
"Scrambled eggs"
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Ah yes I've seen that - what's is drop the dead donkey ? - sorry I don't watch much telly
"We can't stop here - this is bat country" - Hunter S Thompson - RIP
|
|
|
|
|
Early 90's topical comedy show about a TV newsroom - had some very funny episodes. A little dated in patches now, but most of it still works. I think most of it is up on YouTube.
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
H,I,J,K,L,M,N,O / lb
(5,5)
|
|
|
|
|
OriginalGriff wrote: This isn't original to me It looks like it isn't Griff to you either, unless you are changing your moniker to OriginalTommy
|
|
|
|
|
You should all try this: Remove the printing head from a 3D printer, then completely take it apart, clean it out, install a new nozzle and, the greatest part comes last, put it all back together.
Leveled the bed, loaded the filament, so far, so good.
It's printing now and everything looks ok so far, but let's hold the celebration until it's finished...
I have lived with several Zen masters - all of them were cats.
His last invention was an evil Lasagna. It didn't kill anyone, and it actually tasted pretty good.
|
|
|
|
|
I haven't advanced that far yet. I'm still trying to figure out how to prevent warping!
The difficult we do right away...
...the impossible takes slightly longer.
|
|
|
|
|
Try printing the object on supports and at a flat angle, like 5 degrees.
I have lived with several Zen masters - all of them were cats.
His last invention was an evil Lasagna. It didn't kill anyone, and it actually tasted pretty good.
|
|
|
|
|
Not sure I understand this tip.
How would it print at an angle? The nozzle won't know that the object is at an angle and it will behave as though I'm printing flat.
EDIT:
Oh you mean put the whole machine on an angle?
The difficult we do right away...
...the impossible takes slightly longer.
|
|
|
|
|
No. That would not help very much. That's kindof what a mathmatician would seriously contemplate. Instead of simply turning himself by 90 degrees, he could actually come up with the idea to turn the entire universe (or at least the planet) by 90 degrees in the opposite direction instead. Mathmatically ok, but somewhat impractical.
The plastic contracts while it cools down, so it starts pulling at the layer beneath it. The weaker the lower layers are and the longer the new layer is, the stronger that force will be and the more warping you will have. All you have to do is to rotate the object in a way to reduce these effects.
Let's say you want to print a large cube. If it's big enough and you lay it flat on one side, you may get warping at the corners. First layers to be printed will be very thin squares. Try it and pull it off the bed after only printing the first layer. This thin thing has no strength at all and the only thing that keeps it from warping is the adhesion to the bed. The second layer will contract and may pull the corners of the first layer off the bed, resulting in warping.
Why not print the cube balancing on one corner instead? Of course you now need supports and it will take longer to print, but warping will probably not occur at all. If you look at the horizontal cross sections, you will see that the first layers of the balancing cube are so tiny that warping is not an issue. The cross sections only gradually get bigger and by the time that they get wide enough for warping, there are enough layers underneath that can easily resist the pull from a new layer.
I have lived with several Zen masters - all of them were cats.
His last invention was an evil Lasagna. It didn't kill anyone, and it actually tasted pretty good.
|
|
|
|