|
Welcome to the wonderful world of 3D printing.
Wait until you get 2 days into a 3 day print and the power goes out. arrrrrrrg
They call me different but the truth is they're all the same!
JaxCoder.com
|
|
|
|
|
Would not a little work with an Xacto knife, dremel or file resolve the problem?
|
|
|
|
|
For little components, yes. But we're talking about a plate 60x80mm and another 70x80mm ... there is no way I'd get a nice finish over that size. And one of 'em is the "front" plate which has to look right, and the other is the base which sits flush to the wooden box and has the securing lugs.
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
|
Measure twice, print once....
I'd rather be phishing!
|
|
|
|
|
Whenever I think of experimenting with 3D printing I seem to get talked out of it.
| Ravings en masse^ |
|---|
| "The difference between genius and stupidity is that genius has its limits." - Albert Einstein | | "If you are searching for perfection in others, then you seek disappointment. If you seek perfection in yourself, then you will find failure." - Balboos HaGadol Mar 2010 |
|
|
|
|
|
It's actually quite fun in a "learning to think differently" kind of way - and surprisingly handy. It does take up quite a bit of space though - my box around it is basically a 0.5m cube, to keep the noise down, provide ABS fume extraction, and most importantly keep the cat away from it ... 
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Thinking differently - probably a parallel route of thinking came from the combination of machine shop and drafting courses required in my high school (even for college prep).
Drafting gave you the view of items and what's in front vs. what's behind. In layers.
Machine shop gave you the perspective that you don't request what were (then) impossible things, such as drilling a 1/2" hole and the requesting a 1" hole be drill internally with the hole that is 1" wide. Now, using a cutting laser, this is doable. Then, however, you could not put 1" drill down a 1/2" hole, nor even it were a partial wing-shaped cutter, swing it to that 1" dimension.
Oddly not wasted - even for chemistry grad school: When I needed a piece of equipment made, the machinist ("instrument maker" level) always appreciated my diagrams and design plans with the only complaint being that I was taught the European convention for the top view.
Most people, as you infer, never had to think in layers - and even with what I already have it's still going to be quite different. Also, we did our drafting with pencils and paper.
| Ravings en masse^ |
|---|
| "The difference between genius and stupidity is that genius has its limits." - Albert Einstein | | "If you are searching for perfection in others, then you seek disappointment. If you seek perfection in yourself, then you will find failure." - Balboos HaGadol Mar 2010 |
|
|
|
|
|
|
A nice bit of woodworking there, OG!
- I would love to change the world, but they won’t give me the source code.
|
|
|
|
|
Thanks!
The front is held on by magnets, but the whole thing lifts off the base to change filament, etc.
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
just file them down and call it a day. 
When I was growin' up, I was the smartest kid I knew. Maybe that was just because I didn't know that many kids. All I know is now I feel the opposite.
|
|
|
|
|
Quote: I'm an idiot.
Yes, but a 3D one!
|
|
|
|
|
|
I used to read that when I was a kid! 
It's named "Flippie Flink" in Dutch.
Never seen it since, but I'm happy to see it now
|
|
|
|
|
Is a drunk ursine unbearable?
"I have no idea what I did, but I'm taking full credit for it." - ThisOldTony
AntiTwitter: @DalekDave is now a follower!
|
|
|
|
|
Can a bruin brew bearable beer?
Freedom is the freedom to say that two plus two make four. If that is granted, all else follows.
-- 6079 Smith W.
|
|
|
|
|
How much brew would a bruin brew if a bruin could brew brew?
|
|
|
|
|
that's just getting unbearable
oh wait: How much bear beer brew would a bruin bear brew if a bruin bear could brew bear beer brew?
... guess it wasn't 'un-bear-able' after all
Message Signature
(Click to edit ->)
|
|
|
|
|
Yes, but they have to drink a Padding-TON to get drunk. So it's uncommon.
|
|
|
|
|
I have no proof, but den again, it's just a way of being cordial.
| Ravings en masse^ |
|---|
| "The difference between genius and stupidity is that genius has its limits." - Albert Einstein | | "If you are searching for perfection in others, then you seek disappointment. If you seek perfection in yourself, then you will find failure." - Balboos HaGadol Mar 2010 |
|
|
|
|
|
The pun was okay. The responses have been downright grizzly!
I, for one, like Roman Numerals.
|
|
|
|
|
Only when he can't hold his ursine.
Software Zen: delete this;
|
|
|
|
|
Been a few years since dug into the details of putting together a new desktop rig, and thought to ask and share what some of the basic versions of components should be for 2019?
NVMe supported Motherboard
AMD Ryzon cpu over Intel something (price vs performance)
DDR4 - DDR5 is expected for 2020.
Graphics card still look to be easily swap-able regardless of motherboard
Any issues opting for a card with just HDMI ports?
Still drooling over 14TB hdd. But with NVMe as OS drive, any harm doing 2x HDD raid 1 (seperate dedicated nas for more long term storage, this just to boost internal storage with some level of backup. or is performance drain?
For use with gaming, light video editing, and software development.
Any other newish technologies in last 5 ish years, that should be looking out for?
USB-c ports - are these practical on a desktop?
|
|
|
|
|
as long as you have an AMD's Threadripper 3970x, mounted on an ASUS ROG Zenith II Extreme board, with an NZXT Kraken X62 fluid cooler and Corsair Dominator Platinum RAM.
or better buzzwords you should be ok...
I'd rather be phishing!
|
|
|
|
General 
News 
Suggestion 
Question 
Bug 
Answer 
Joke 
Praise 
Rant 
Admin 
Submit an article or tip
