|
|
|
rotflmao !! this one is excelent 
|
|
|
|
|
toxcct wrote: rotflmao !! this one is excelent
I mean, this is the best I could give to someone like him over the internet. 
Nobody can give you wiser advice than yourself. - Cicero
ப்ரம்மா
|
|
|
|
|
|
Absolutely wonderful! Hi-5, my-5!
I didn't see the original post, but your reply is priceless.
"It's supposed to be hard, otherwise anybody could do it!" - selfquote
"High speed never compensates for wrong direction!" - unknown
|
|
|
|
|
Roger Stoltz wrote: Absolutely wonderful! Hi-5, my-5!
I didn't see the original post, but your reply is priceless.
Thanks
Original post was "hallo" and the post subject was "dsd". He deserves real slap(s), rather than "Virtual Slaps".
Nobody can give you wiser advice than yourself. - Cicero
ப்ரம்மா
|
|
|
|
|
brahmma wrote: He deserves real slap(s), rather than "Virtual Slaps".
Second that.
But this is the best that can be done until the act of polluting the forum like this is punishable by a fine. A new market for PayPal perhaps...
"It's supposed to be hard, otherwise anybody could do it!" - selfquote
"High speed never compensates for wrong direction!" - unknown
|
|
|
|
|
Must be checking, if CP forums are working properly.
|
|
|
|
|
prasad_som wrote: He Must be checking, if CP forums are working properly.
Agreed. I just provided a link so that he can understand even hyperlinks work properly in CP.
Nobody can give you wiser advice than yourself. - Cicero
ப்ரம்மா
|
|
|
|
|
|
how to bind groupbox and radiobuttons.or is any container for radiobutton.when i move a container alongwith the radiobuttons also moved
how to perform this.give samples
|
|
|
|
|
I doubt if I get your question properly. Are you asking how to group a few radio buttons together so that only one of them could be selected? For this, you first insert a few radio buttons, go to the first radio button's property, and enable the "Group" checkbox (And uncheck this property for other radio buttons). Now this would for a group of mutually exclusive radio buttons.
PS: The group box is just a visual representation and it won't group the controls together.
Nobody can give you wiser advice than yourself. - Cicero
ப்ரம்மா
|
|
|
|
|
void thread1()<br />
{<br />
do {<br />
....<br />
} while(g_nData == 0);<br />
}<br />
<br />
void thread2()<br />
{<br />
if (g_nData == 1)<br />
{<br />
....<br />
}<br />
}<br />
<br />
void thread3()<br />
{<br />
if (...)<br />
{<br />
InterlockedExchange(&g_nData, 0);<br />
}<br />
else if (...)<br />
{<br />
InterlockedExchange(&g_nData, 1);<br />
}<br />
else<br />
{<br />
InterlockedExchange(&g_nData, 2);<br />
}<br />
}
1. If when thread1() reading g_nData, thread2() write g_nData, whether read first or write first?
2. If when thread2() writing g_nData, thread1() read g_nData, whether wait read done or read first? the g_nData vaule is thread2() write vaule? or old value?
3. If i want keep g_nData write first, how to do?
thanks.
|
|
|
|
|
hi i am having three radio buttons. how to align these in the center of the screen. i used setwindows position. it works well in my system. but when i tested in any otjer. it was placed in soe other position. what i have to do
Arise Awake Stop Not Till ur Goal is Reached.
|
|
|
|
|
You can use of WM_SIZE for set position of them.
|
|
|
|
|
Can you show code, you are using ?
|
|
|
|
|
yes here it is
CColorButton m_CleanOption;
CColorButton m_NetOption;
CColorButton m_AuthenOption;
m_CleanOption.SubclassDlgItem(IDC_CLEAN,this);
m_CleanOption.SetWindowPos(&CWnd::wndBottom, x-(x/3)-250, y-(y/2)+5, 150,25,m_CleanOption.ShowWindow(SW_SHOW));
m_NetOption.SubclassDlgItem(IDC_NETCONFIG,this);
m_NetOption.SetWindowPos(&CWnd::wndBottom, x-(x/3)-250, y-(y/3)-130, 150,25,m_NetOption.ShowWindow(SW_SHOW));
m_AuthenOption.SubclassDlgItem(IDC_AUTHENICATION,this);
m_AuthenOption.SetWindowPos(&CWnd::wndBottom, x-(x/3)-250, y-(y/4)-177, 150,25,m_AuthenOption.ShowWindow(SW_SHOW));
Arise Awake Stop Not Till ur Goal is Reached.
|
|
|
|
|
deeps_cute wrote: m_CleanOption.SubclassDlgItem(IDC_CLEAN,this);
m_CleanOption.SetWindowPos(&CWnd::wndBottom, x-(x/3)-250, y-(y/2)+5, 150,25,m_CleanOption.ShowWindow(SW_SHOW));
What is x here ?
You need to calculate center location of dialog dynamically(not hardcoding some value, 250 in this case).
Different computers have different resolution,such hardcoding causes problem then.
|
|
|
|
|
i used WM_SIZE method to get the x and y value
Arise Awake Stop Not Till ur Goal is Reached.
|
|
|
|
|
Problem in this case, as said earlier ,is using hardcoded value like 250, why it is so ?
|
|
|
|
|
then how to use this. if i removed the hardcode i cant arrange the button
Arise Awake Stop Not Till ur Goal is Reached.
|
|
|
|
|
thank you friend i got the solution. i removed hard code. now its working well
Arise Awake Stop Not Till ur Goal is Reached.
|
|
|
|
|
How are events processed in Document/View Architecture?I am confused regarding that which class is first invoked to handle that event & then where control will go on?Please reply as soon as possible.
Thanks & Regards
Pankaj
|
|
|
|
|
General 
News 
Suggestion 
Question 
Bug 
Answer 
Joke 
Praise 
Rant 
Admin 
Submit an article or tip
