A Functor that deletes Pointers from STL Sequence Containers






4.48/5 (16 votes)
A policy based deletion functor that can be used with for_each function.
Introduction
A great thing about STL containers is the way they automatically handle memory for us. By using standard sequence containers such as vector or deque instead of directly dealing with operators new[]
and delete[]
, we avoid possibilities of memory leaks and make our code exception-safe. For instance, if we need a dynamic array of integers within a function, if we use std::vector<int>
rather than int*
, we would be relieved from worrying about calling delete to free up the memory before we exit the function:
vector<int> vectorArray (30); // the memory will be automatically freed ... int* oldStyleArray = new int[30]; // be sure to call delete[] oldStyleArray;
However, things get more complicated if we put pointers into a standard container:
struct C { char data_[50]; }; ... vector <C*> dataArray; for (int i = 0; i < 20 ; ++i) dataArray.push_back(new C());
After dataArray
goes out of scope, only the memory occupied by the pointers itself will be freed, but the objects themselves will stay undeleted unless we do something like:
for (vector <C*>::iterator it = dataArray.begin(), it != dataArray.end(); ++it) delete *it;
before dataArray
goes out of scope.
The best way to deal with this issue is to never put raw pointers into containers, but to use smart pointers, such as boost::shared_ptr
[1], or Loki::SmartPtr
[2]:
vector <boost::shared_ptr<C> > dataArray; for (int i = 0; i < 20 ; ++i) dataArray.push_back(boost::shared_ptr<C> (new C()));
Now, we won’t need to care about freeing up the objects.
However, in some instances we still may want to keep raw pointers in STL sequence containers, and in that case we may use some easier way to clean up the memory than hand-writing the loop. One common solution is to write a functor that would give us possibility of using an STL algorithm such as for_each
[3].
for_each(dataArray.begin(), dataArray.end(), del_fun<C>());
This approach is better, but it still leaves a lot to be desired. For one thing, it always calls operator delete
, which is not appropriate for the cases where the objects are created with new[]
or malloc
. Also, in some cases we may want to zero the pointers after we delete them.
To address these issues, I implemented a policy-based functor free_ptr
.
Design of free_ptr
When using a functor for deleting objects, we are faced with two orthogonal decisions:
- Which function to use for deleting objects?
- Do we zero the pointers after deletions?
To give the user a choice to make the decisions, I used two separate policies: CleanUpPolicy
and ZeroPtrPolicy
:
template <typename T, class CleanUpPolicy = DeleteSingleObject, class ZeroPtrPolicy = DontZeroPtr> struct free_ptr : std::unary_function <T*, void> { void operator()(T*& ptr) { CleanUpPolicy::Destroy(ptr); ZeroPtrPolicy::Zero(ptr); } };
Thanks to the policy-based design, free_ptr
is very simple to use, and yet highly customizable. For the most common scenario (single objects created with new, no need to zero pointers), it can be used like this:
for_each(dataArray.begin(), dataArray.end(), free_ptr<C>());
If the objects were created with new[]
, and we need to zero the pointers after deletion, we write something like:
for_each(dataArray.begin(), dataArray.end(), free_ptr<C, DeleteArray, ZeroPtr>());
For the CleanUpPolicy
, we have the following choices:
DeleteSingleObject
(default) – callsdelete
for each pointer.DeleteArray
– callsdelete[]
for each pointer.Free
– callsfree()
for each pointer.
For the ZeroPtrPolicy
, we have two choices:
DontZeroPtr
(default) – does nothing.ZeroPtr
- sets each pointer to zero.
In ideal world, we would not even need CleanUpPolicy
– if a pointer to a single object was a distinct type than a pointer to array of objects we could have used some template metaprogramming to recognize the right scenario at compile time. However, since this obviously is not the case, I tried to figure out some run-time mechanism to do that. I failed miserably: there does not seem to be a good way to distinguish whether a memory was allocated by new
, new[]
or malloc
if we only have a pointer to this memory. I tried even some non-portable tricks, such as using _memsize
to determine the size of the allocated memory block, however, even if we know the amount of allocated memory, it still does not necessarily shows us the number of objects pointed by the pointer. Therefore, the best I could come up with was CleanUpPolicy
. One good thing with this solution is that in case of some custom memory-management schema, it would be very easy to write another CleanUpPolicy
class and use it as easily as the ones I provided.
I should probably add that usage of free_ptr
will not protect you from some bad programming practices. For instance, if you do something like:
vector <C*> dataArray; dataArray.push_back(new C()); //single object dataArray.push_back(new C[10]); //array of objects dataArray.push_back((C*)malloc(sizeof(C))); // malloc-ed object
then free_ptr will not help you. As I said, it is unfortunate that the previous example will compile at all, but this is just another C-legacy that makes C++ less perfect.
Conclusion
I hope that this little article is useful in two ways: it demonstrates policy-based design, a powerful methodology for developing C++ libraries, and it also provides you with a cool little piece of code that you can find useful in your daily programming tasks.
References
- [1] Boost Smart Pointers, http://www.boost.org/libs/smart_ptr/smart_ptr.htm
- [2] Andrei Alexandrescu: Modern C++ Design – Generic Programming and Design Patterns Applied, Addison-Wesley 2001.
- [3] A del_fun Function Adaptor for STL Containers, http://www.geocities.com/w_steiner/Professional/del_fun.html